| Item type |
学術雑誌論文 / Journal Article(1) |
| 公開日 |
2010-08-23 |
| タイトル |
|
|
タイトル |
マイクロルート研削加工における超音波振動の効果 |
| 言語 |
|
|
言語 |
jpn |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Micro-Route Grinding |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Diamond Quill |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Fine Ceramics |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Ultrasonic Vibration |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Grinding Force |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Cutoff-Surface Roughness |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
Cutoff Accuracy |
| 資源タイプ |
|
|
資源タイプ識別子 |
http://purl.org/coar/resource_type/c_6501 |
|
資源タイプ |
journal article |
| 著者 |
水野, 雅裕
井山, 俊郎
浜田, 智和
庄司, 克雄
厨川, 常元
|
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
61870 |
|
|
姓名 |
MIZUNO, Masahiro |
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
61871 |
|
|
姓名 |
IYAMA, Toshirou |
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
61872 |
|
|
姓名 |
HAMADA, Tomokazu |
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
61873 |
|
|
姓名 |
SYOJI, Katsuo |
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
61874 |
|
|
姓名 |
KURIYAGAWA, Tsunemoto |
| 著者(機関) |
|
|
値 |
岩手大学工学部 |
| 著者(機関) |
|
|
値 |
岩手大学工学部 |
| 著者(機関) |
|
|
値 |
東芝機械(株)沼津事業所 |
| 著者(機関) |
|
|
値 |
東北大学工学部 |
| 著者(機関) |
|
|
値 |
東北大学工学部 |
| 登録日 |
|
|
日付 |
2010-08-23 |
| 書誌情報 |
日本機械学會論文集. C編
巻 60,
号 580,
p. 4349-4354,
発行日 1994-12-01
|
| ISSN |
|
|
収録物識別子タイプ |
ISSN |
|
収録物識別子 |
0387-5024 |
| Abstract |
|
|
内容記述タイプ |
Other |
|
内容記述 |
The micro-route grinding system was developed for efficient micro-cutoff and micro-slotting of fine ceramics. However, because of the use of a very thin electroplated diamond quill, it has several problems in the machining performance : elastic deflection and fracture of the quill, and chipping and large cutoff-surface roughness. To solve these problems, ultrasonic vibration was applied to the workpiece perpendicularly to the machining direction. The obtained results from some cutoff experiments of Sr-Ferrite ceramics are summarized as follows. (1) By means of ultrasonic vibration, the grinding force is decreased by about 30% at the maximum, and the number of large-size chippings on the upper edge of the cutoff workpiece surface is decreased. Furthermore, the ten-point average roughness R_z of the cutoff workpiece surface measured in the quill axis direction is decreased by about 30%. (2) In the case that a quill cuts off a workpiece while rotating in a clockwise direction, the quill deflects backward to the left of the cutting direction. Here, the deflection size is decreased by ultrasonic vibration, and the cutoff accuracy is enhanced. (3) In the case of the use of an eccentric quill, the width of the obtained cut-out groove is increased by ultrasonic vibration. |
| 出版者 |
|
|
出版者 |
社団法人日本機械学会 |
| 権利 |
|
|
権利情報 |
copyright (c) 社団法人日本機械学会 |
| 著者版フラグ |
|
|
出版タイプ |
VoR |
|
出版タイプResource |
http://purl.org/coar/version/c_970fb48d4fbd8a85 |
tjsmec-v60n580p4349-4354 (504.0 kB)
