| Item type |
学術雑誌論文 / Journal Article(1) |
| 公開日 |
2010-11-19 |
| タイトル |
|
|
タイトル |
ダイヤモンドクイルによるマイクロルート研削に関する研究 |
| 言語 |
|
|
言語 |
jpn |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
micro-route grinding |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
diamond quill |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
ceramics |
| キーワード |
|
|
主題Scheme |
Other |
|
主題 |
workpiece oscillation |
| 資源タイプ |
|
|
資源タイプ識別子 |
http://purl.org/coar/resource_type/c_6501 |
|
資源タイプ |
journal article |
| 著者 |
水野, 雅裕
井山, 俊郎
浜田, 智和
庄司, 克雄
厨川, 常元
|
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
62235 |
|
|
姓名 |
MIZUNO, Masahiro |
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
62236 |
|
|
姓名 |
IYAMA, Toshirou |
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
62237 |
|
|
姓名 |
HAMADA, Tomokazu |
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
62238 |
|
|
姓名 |
SYOJI, Katsuo |
| 著者別名 |
|
|
|
識別子Scheme |
WEKO |
|
|
識別子 |
62239 |
|
|
姓名 |
KURIYAGAWA, Tsunemoto |
| 著者(機関) |
|
|
値 |
岩手大学工学部 |
| 著者(機関) |
|
|
値 |
岩手大学工学部 |
| 著者(機関) |
|
|
値 |
岩手大学大学院 |
| 著者(機関) |
|
|
値 |
東北大学工学部 |
| 著者(機関) |
|
|
値 |
東北大学工学部 |
| 登録日 |
|
|
日付 |
2010-11-19 |
| 書誌情報 |
砥粒加工学会誌
巻 38,
号 2,
p. 95-100,
発行日 1994-03-01
|
| ISSN |
|
|
収録物識別子タイプ |
ISSN |
|
収録物識別子 |
0914-2703 |
| Abstract |
|
|
内容記述タイプ |
Other |
|
内容記述 |
There are several problems in the micro-route grinding of ceramics with electroplated diamond quill: fracture of
quill, elastic deformation of quill, dulling of the cutting grain edges, large roughness of the cut-off surface and so on. These all come from the thinness of the quill. For the purpose of solving these problems, cutoff experiments were carried out under two kinds of grinding conditions. One was under oscillating workpiece in the spinde axis direction and the other was under swinging the spindle in its axis direction. The experimental results are summarized as follows. (1)Under no oscillation of workpiece, the grinding force doesn't decrease with the reduction of the
tabl speed. (2)When oscillating workpiece, the grinding force becomes remarkably small with the increase of workpiece frequency if the table speed is small. (3)However, the effect of workpiece oscillation becomes small when the table speed is high. (4)The roughness of cut-off surface is improved by increasing the workpiece frequency. (5)When swinging the spindle at low frequency and in large amplitude, the roughness of cut-off surface in the table feed direction becomes large because of the cyclic changing of the tool deformation. |
| 出版者 |
|
|
出版者 |
砥粒加工学会 |
| その他のタイトル |
|
|
その他のタイトル |
Study on Micro-Route Grinding with Electroplated Diamond Quill |
| 著者版フラグ |
|
|
出版タイプ |
VoR |
|
出版タイプResource |
http://purl.org/coar/version/c_970fb48d4fbd8a85 |
jjsat-v38n2p95-100.pdf (399.4 kB)
